[olug] PCI Wireless

Sean Edwards cybersean3000 at yahoo.com
Tue Feb 1 15:29:09 UTC 2005


I already have a 486 running as a router/NAT box with
a Coyote Linux boot floppy.

I was hoping to upgrade my Coyote box to an old
Pentium with a PCI slot, and run the Linksys WAP11 as
a Host Access Point.  That is how this all started. 

-=Sean Edwards=-

--- "Shawn L. Djernes" <shawn at djernes.org> wrote:

> Well if you are looking at getting a "real" AP then
> look at the WRT54g.
> Yes, it is a router and you may not need a router. 
> It has so many more
> features for the same cost or less of an AP.
> 
> 1.	Its a switch
> 2.	Its Radio can be set in many modes (AP, client,
> bridge, repeater)
> 3.	It Runs Linux !!!!
> 4.	If you need a quick router in an emergency (LAN
> party, main one dies,
> installfest)
> 5.	Cheapest way to get a 4 port Wireless Bridge.
> 
> Shawn
> 
> -----Original Message-----
> From: olug-bounces at olug.org
> [mailto:olug-bounces at olug.org]On Behalf Of
> Sean Edwards
> Sent: Tuesday, February 01, 2005 12:51 AM
> To: olug at olug.org
> Subject: [olug] PCI Wireless
> 
> 
> Well, I finally got around to messing with the
> Linksys
> WAP11 PCI card from Jay.
> 
> First of all, I had to figure out how to load the
> Windows driver.  The two options were the Linuxant
> driverloader, and Open Source ndiswrapper.  Although
> I
> had all the pieces, the Windows driver and the card,
> Linuxant wanted $20 for a license.  Needless to say,
> I
> went with ndiswrapper.
> 
> It was pretty easy to load ndiswrapper with the
> Windows driver, and configuring it with iwconfig was
> fairly easy too.
> 
> Setting up the wireless network as ad-hoc was very
> simple, no surprises there.  I even discovered the
> wireless network with KisMac on my G4.  Then things
> went bad.  Even though the the network information
> was
> broadcasting, I could not ping either remote end of
> the wireless connection.
> 
> As it turns out, there are a couple of versions of
> the
> Linksys WAP11 PCI card.  One version uses a Prism 2
> chip set, while the newer version uses a Broadcom
> chip
> set.  I also found out that the Prism 2 chip set
> version of the card can run as a Host Access Point
> with Linux, and the Broadcom chip set version of the
> card can not.  It appears to be a problem which
> starts
> with Broadcom not providing software or
> documentation
> to the Linux community to facilitate drivers for
> this
> card.
> 
> I am sure the Linksys WAP11 PCI Broadcom card will
> work fine in my Linux desktop PC to access a WAP of
> some sort, but I don't have a wireless access point
> right now to test it. (I was trying to create one!)
> 
> -=Sean Edwards=-
> 
> 
> 
> 
> 
> 
> __________________________________
> Do you Yahoo!?
> Meet the all-new My Yahoo! - Try it today!
> http://my.yahoo.com
> 
> 
> _______________________________________________
> OLUG mailing list
> OLUG at olug.org
> http://lists.olug.org/mailman/listinfo/olug
> 
> 
> 
> 



		
__________________________________ 
Do you Yahoo!? 
Meet the all-new My Yahoo! - Try it today! 
http://my.yahoo.com 
 




More information about the OLUG mailing list